BRAVO ACCESSORIES

 

DRIVE COOLING SHOWER 
BDCS
- Modern sleek fitted drive shower for - Bravo, XR & ITS
- All stainless steel w/ optional kit for XR & ITS outdrives    with finned caps
- Unit is coupled with a high volume pickup & #10 stainless steel braided hose
- Engineered to get maximum cooling from a series of water diverters and dams to allow equal water distribution
 
DRIVE COOLING SHOWER BDCS $ 189
DRIVE SHOWER HOSE FOR LATHAM
- Stainless braided hose
- 90° fitting
- Screws into Latham top steering plate
 
DRIVE SHOWER HOSE FOR LATHAM DSHL $ 132
     
ULTIMATE BRAVO DRIVE SHOWER
- NO more drilling holes in your drive!
- Drive shower mounts to the drives tilt ram
-15 dump ports targets only the sides & back of the drive
- Multiport system distributes continuous cool water flow  to top of the stern drive
- Lowers oil & bearing temps, lowers operating temp by 60°
- Promotes maximum drive durability
-Fits all Bravo drives including ones w/ Imco or Latham steering, that mounts to back of the drive
- Made of Stainless Steel
 
ULTIMATE BRAVO DRIVE SHOWER BDSU $ 239

 


Standard Bravo             (prior to 2004)       

DSSB     $196

 

Bravo with finned top cap and/or Latham or Imco steering using back cap 

DSSB     $196

 
 

    Drive Shower Hose for Latham

Stainless braided hose with 90° fitting, screws into Latham top steering plate.

DSHL          $132

MULTIPORT DRIVE SHOWERS

     If there is a continues need to remove a white chalky deposit from the top half of your drive, or you are constantly topping off your drive oil reservoir, your drive is probably running TOO HOT!!! Other problems that some of our customers have had are: a case of "the mysterious drive oil consumption", paint on the top half of the drive is dull or brownish, a cloud of steam that appears every time your boat comes off plane, your drive oil reservoir bottle keeps overflowing or has burst.

     This multi-port system distributes a continues supply of cool water to the top portion of the stern drive. Tests have shown that cooling like this can double the bearing life and service life of the drive oil by lowering an operating temperature of 220° to 350° by 60°. It prevents oil foaming, the primary cause of oil break down which can lead to drive failure. This condition exists on nearly every boat, but is especially prevalent in a high performance application where demands on the drive are pushed to the limit.

     This new design produces a much higher water volume than any other drive cooling system because it uses two intake ports instead of only one. It is capable of delivering 1 gallon per second of cooling water to the top of the drive at a boat speed of 40 MPH. It's eleven strategically placed dump ports target only the sides of the drive and doesn't waste any of it's cooling water on the top bearing cap. The sides are the only place where the material is thin enough to wick 60° of heat off the drive oil, the bearing cap if far too thick. This two sided design also eliminates the need for a left and right hand version in a twin stern drive application. All components are made of stainless steel and come with a full one year warranty against manufacturing defects. Templates and mounting hardware is included.

 

 

If your external steering uses a "wing plate",

call us for a custom drive shower.

top

DRIVE SHOWER DELUXE

  • Easily installed on Bravo and XR drives
  • Lowers oil & bearing temperatures
  • Promotes maximum drive durability & longevity
  • Cooling water is dispersed evenly over top of drive
  • Stainless braided hose for pickup

BDS                    $203

top  

DRIVE TEMP
GAUGE


2 1/16" cutout,
2 3/8" overall
or
2 5/8" cutout,
2 3/4" overall

from $87

  • Warns you of unseen dangerous drive conditions, high drive temperature                           or failure on stern drives
  • Alerts you of partial seal failure or friction related problems
  • 28" stainless braided hose for pickup
  • For easy installation, sender mounts in drive vent hole
add size add k1 for kit add dial color add s for super rim add rim color

Part # example

GIDT   W   W

standard
2 1/16” cutout, 2 3/8” overall
gauge only    GIDT
full kit           GIDTK1

monster
2 5/8” cutout, 2 3/4” overall
gauge only     LMDT
full kit            LMDTK1
 

note: above for mercury
products only, other kits
available

Kit items

gauge

harness

thru-hull fitting

sender
 

2” black and white only

BlacK
Carbon Fiber
PLatinum
W
hite
Super rim not available on 2”

No “S” needed if ordering standard rim

Black - BK
Blue - BL
Chrome - CH
Lime - L
Mustard - MU
Orange - O
Platinum - PL
Purple - PU
Red - R
Tangelo - TA
Teal - T
White - W



 
STANDARD SIZE (extra long same price*)
Black dial w/black rim gauge only from $87
Black dial w/black rim kit from $349

MONSTER SIZE (extra long same price*)
Black dial w/black rim from $123
Black dial w/black rim kit from $369

Platinum dial w/platinum rim gauge only $114
Platinum dial w/platinum rim kit $369

 
White dial w/white rim gauge only from $87
White dial w/white rim kit from $349

White dial w/white rim gauge only from $123
White dial w/white rim kit from $369


Carbon fiber dial gauge only (add rim and $) $133
Carbon fiber dial kit (add rim and $) $379


*Longer length assembly available for extension boxes, add XL prior to dial color
Drive temp assembly only DTA $234          Drive temp assembly only - extra long DTAXL $234
Standard: add $8 for colored rim, super rim not available on 2"
Monster: add $8 for colored or super rim, add $11 for chrome super rim


The Super Bezel is a registered trade mark of Auto Meter Products, Inc.
*This is in reference to all Super Bezels throughout the Livorsi website

top


SPACER KITS for BRAVO
and SPORTMASTER DRIVES

  • Adjust your drive height for increased performance and improve MPH without removing the engine or drives
  • Perfect for R & D testing on any boat style
  • Kit comes complete with all necessary fittings
  • Anodized black to match drives
  • Available in 1/2, 1, 1 1/2, 2, 2 1/2 or 3”

Coupler kits and stud set kits are available for all sizes, please call 877-548-5900 for more info

Bravo

1/2"       BS1/2          $713 1"          BS1            $799    1 1/2"    BS11/2        $976    2"          BS2            $1091   2 1/2"    BS21/2       $1164   3"          BS3            $1295

Sportmaster

1/2"       SMS1/2     $797  1"          SMS1        $951   1/2"     SMS11/2   $1152   2"          SMS2        $1351  1/2"     SMS21/2   $1539 3"          SMS3        $1845

 
 
top

 


Bravo Prop Wrench   BPW   $46

BRAVO WRENCH
  • 1 1/16” socket 4” deep to clear cavitations plate
  • Turn nut without hitting cavitations plate
  • Recommended for Mercruiser / Mercury OB 75hp and up
  • Fork lift tab locks
top

 

   

top

<< previous page

 
 

Home  |  About Livorsi Marine  |  Tech Tools  |  FAQ  |  Products  |  Related Sites  |  Contact Us

 Livorsi Marine Inc. 715 Center St. Grayslake, IL 60030  sales@livorsi.com

Copyright © 2005 Livorsi Marine, Inc.  All Rights Reserved.