If this message is not displaying properly, click here to launch your browser.

Livorsi GPS Pulse Antenna

GPS Pulse Antenna

For Use With Any Electric Automotive or Commercial Speedometer
With 8K or 16K Pulse Signal

Convert your electronic automotive speedometer into a GPS speedometer with this GPS Pulse Antenna. The antenna receives GPS satellite signals and outputs the information to 8,000 or 16,000 pulse signal to your existing speedometer. This antenna eliminates connections to the transmission or the need to calibrate to your vehicles tire size.

This fast update antenna receives signals 10Hz (10 per second) driving your speedometer to display your true speed (no pointer lag). This antenna is a stand alone device, which does not require a membership fee for GPS service. The antenna can be mounted under the dash or in an other hidden area as long as you verify the speedometer is working properly before permanently mounting the antenna.

Accuracy and ease of installation makes this GPS Pulse Antenna an affordable solution if you are looking to upgrade to a GPS speedometer system.

  • Outputs 8,000 or 16,000 pulse signal to work with your existing electronic speedometer
  • Eliminates cables to transmission
  • No calibration needed
  • 10Hz update for real time data (10 per second)
  • 2 3/4 in. L x 2 3/8 in. W x 7/8 in. H
  • Operating voltage is 10-32V DC, unit typically consumes < 50Ma at 12V
  • 4 foot harness with ring terminals to connect to threaded #8-32 studs

Part Number: GPSESQ3
Category III

Download Press Files

Fuel and Water Level Senders

SFW sender

Measurement is done by series of reed switches positioned inside the level tube. A float with built in magnets then triggers the reed relays generating a potential - free resistance with an ohm value that increases or decreases.

The float is the only moving part of the sensor, thereby minimizing potential mechanical failures. All sensors are fully insulated to protect against voltage inside the tank.

  • Available from 4 inches to 36 inches
  • 316 Stainless Steel
  • SAE 5 Hole Pattern
  • 240-33 OHMS
  • Other resistances available upon request
  • Constructed to meet and/or exceed all applicable ISO standards
  • Optional threaded NPT Adapter for screw in applications
  • Sensors are fully insulated to protect against voltage inside the tank
  • Float is the only moving part of the sensor, minimizing mechanical failure

For more information on these senders, click here

Download Press Files

International Workboat Show

Booth# 479

Livorsi will be exhibiting at the International Workboat Show taking place November 30th through December 2nd in New Orleans.

Attend the International Workboat Show for FREE, compliments of Livorsi Marine, Inc. Click here to register.

Visit the official International Workboat Show web site for more information.

Links

To request an industrial catalog, click here

Request a Livorsi Marine, Inc. catalog


To request a new catalog, click here

Request a Livorsi Marine, Inc. catalog

The #1 Choice in Performance Boating!

www.livorsi.com
715 Center St.                        Grayslake, IL 60030                        P: 877-548-5900                        F: 847-752-2415

Livorsi and the Livorsi logo are either registered trademarks or trademarks of Livorsi Marine, Inc. in the United States and / or other countries.

© 2011 Livorsi Marine, Inc. All rights reserved.

PLEASE DO NOT REPLY TO THIS MESSAGE. To obtain information on how to contact Livorsi, visit us on the web at: http://www.livorsi.com, or call 877-548-5900. This is an advertising message from Livorsi Marine, Inc. If you would prefer not to receive e-mail like this from Livorsi Marine in the future, please send an e-mail to info@livorsi.com. Alternatively, you may mail your unsubscribe request to Livorsi Marine at the following address:

UNSUBSCRIBE
Livorsi Marine
715 Center St.
Grayslake, IL 60030